Pro Solar Panama 800mm Solar Powered LED Bollard Light – CCT
The Pro Solar Panama is a professional-quality 800mm solar powered bollard light, ideal for illuminating garden paths, driveways, walkways and outdoor entrances without the need for mains electricity.
Finished in black die-cast aluminium, the Panama features a wide anti-glare top and a specially designed polycarbonate lens to distribute light downwards and evenly across surrounding surfaces.
The updated CCT model incorporates a colour temperature switch, allowing you to choose between warm white (3000K) and daylight white (6000K) illumination from the same fitting.
Key features
2W integrated LED producing approximately 220–240 lumens
Switchable 3000K warm white or 6000K daylight white
Automatic dusk-to-dawn illumination
Intelligent dimming sequence to conserve battery power
High-efficiency 5V / 3.5W monocrystalline solar panel
Replaceable 3.2V / 12Ah LiFePO4 lithium battery
Anti-glare top with 120° beam angle
Black die-cast aluminium body and impact-resistant polycarbonate lens
IP65 weather protection
IK10 impact-rated main body
Tamper-resistant security screws
No mains wiring required
800mm overall height
5-year guarantee
Switchable warm white or daylight white illumination
The Panama CCT offers flexibility when choosing the appearance of your outdoor lighting.
Select 3000K warm white for a softer, welcoming effect around gardens, patios and residential pathways, or choose 6000K daylight white for a brighter-looking, cooler illumination.
The colour temperature can be changed using the fitting's integrated switch, so there is no need to purchase separate warm white and daylight white models.
Automatic dusk-to-dawn lighting
The Panama uses a light sensor to switch on automatically as daylight fades.
Its intelligent lighting controller gradually reduces brightness throughout the night, helping to preserve stored solar energy.
The programmed lighting sequence is:
First hour: 100% brightness
Following 2 hours: 80% brightness
Following 2 hours: 50% brightness
Following 9 hours: 30% brightness
The Active Smart Power System (ASPS) can further reduce light output when battery voltage is low, helping to extend operating time.
Under suitable charging conditions, the fitting offers up to 23 hours of illumination from a full charge. Actual performance will depend on the available sunlight and seasonal conditions.
Efficient solar charging and replaceable battery
The integrated monocrystalline solar panel charges the internal lithium battery during daylight hours.
A full charge typically requires approximately 6–8 hours of suitable direct sunlight.
The 12Ah LiFePO4 battery is replaceable, helping to extend the useful life of the bollard without replacing the complete fitting.
Durable construction and straightforward installation
The Panama is designed for permanent outdoor installation, with an IP65 weather-resistant construction and a robust die-cast aluminium body.
The standard fitting is suitable for surface mounting on an appropriate solid base. Alternative ground installation accessories may also be available.
No mains electrical connection is required, making the Panama a practical lighting solution for locations where running electrical cables would be difficult or expensive.
For best performance, install where the solar panel receives unobstructed daylight, avoiding excessive shading from trees, buildings and other structures.
Please note: Installation very close to the coast may affect the finish of the fitting. Always refer to the manufacturer's installation instructions before fitting.
Warranty and delivery
Manufacturer's guarantee: 5 years
Expected LED life: up to 50,000 hours
Typical delivery: 2–3 working days, subject to availability
Specifications
| Beam Angle | 120° |
|---|---|
| Bollard Height | 800mm |
| Colour | Black |
| Diameter | 145mm |
| IP Rating | IP65 |
| Colour Temperature | 6000K |
| Lumens | 210 lm |
| Materials | Aluminium / Polycarbonate |
| Mounting Option | Standard surface mount |
| Solar Panel | 5V / 3.5W Monocrystalline |
| Warranty | 5 Years |
| Watts | 1.8W |
| Weight | Approx. 4.75kg |
| IK Rating | IK10 Body / IK06 Lens & Solar Panel |
| Battery | 3.2V / 12Ah LiFePO4 (Replaceable) |
| Charging Time | Approx. 6–8 hours in full sunshine |
| Illumination Time | Up to 23 hours from a full charge |
| LED Life | Up to 50,000 hours |
| Solar Control | Automatic dusk-to-dawn with dimming |
| Top Diameter | 255mm |
Downloads
-
Panama-CCT-800mm-Installation-Manual.pdf
pdf, 346.6 KB
PRODUCT AFTERCARE
Although each of our light fittings come with a warranty, it is also important to take care for your product after installation. The outdoor environment can be harsh with very warm and hot conditions as well as extremely cold, wet, and windy conditions and more especially in coastal areas where the salt air is more concentrated causing corrosion. By neglecting to care for your product may void any warranties. Below is information on caring for the different type of products we sell.
COPPER, BRASS & BRONZE
Brass and Bronzes are families of copper-based alloys and mainly copper and zinc. Bronzes are mainly copper along with alloying elements such as tin, aluminium, silicon, or beryllium. Brass generally has a bright gold appearance dependent upon the percentage of copper yields, the higher the percentage the rosier the tone will be, and more zinc will make it appear silvery. Brass has higher malleability than bronze or zinc and is ideal for resisting corrosion including galvanic corrosion from saltwater. Copper products start off with a shiny orange appearance and once installed copper weathers naturally to a lovely blue-green colour or patina over time. In arid climates, the colour change is usually to a nut brown. The colour change is the result of surface oxidation caused mainly by moisture and corrosive elements in the atmosphere. Unlike rust oxidation, the copper patina is a protective barrier that retards further corrosion, to maintain copper’s long life. They are ideal for coastal areas and to keep them looking pristine we recommend cleaning copper surfaces periodically with a solution of salt and vinegar to remove any excess deposits. Simply dissolve salt in vinegar, then use a soft cloth to apply the liquid solution to the surface of the fitting then buff until you see the copper begin to shine. Rinse and dry. The ‘Brasso’ product is a metal polish designed to remove deposits from brass, copper, chrome, and stainless steel. WD 40 is also useful for cleaning brass too and wipe off with soapy water.
316L & 316 STAINLESS STEEL
The highest grade of Stainless Steel we use is 316L Marine Grade Stainless Steel which is a low carbon version of 316 Stainless Steel (which is why it has L after the 316). These grades of Stainless Steel are popular for use in Coastal areas due to the materials immunity from boundary carbide precipitation (sensitisation). However, 316 Stainless Steel contains more carbon and although is still corrosion resistant it does still need care to remove the deposits that build up on the surface or the corrosion will eventually start to build up on the surface. We sell more 316 than 316L products on this website. The elements of 316L and 316 Stainless Steel are Carbon, Manganese, Phosphorous, Sulphur, Silicon, Chromium, Nickel, Molybdenum, Nitrogen, and Iron. The only difference is that 316L has 0.03 max % of Carbon and 316 has 0.8 max % of carbon. To maintain the shiny clean surface of 316L and 316 Stainless Steel we recommend the use of Stainless-Steel cleaning products or a solution of lemon juice and baking powder and wiped off with soapy water.
304 STAINLESS STEEL
304 Stainless Steel is made up of Carbon, Manganese, Phosphorous, Sulphur, Silicon, Chromium, Nickel, Nitrogen, and Iron. There is no presence of Molybdenum the anti-corrosive element and this metal has a high carbon content too. Therefore, we would not recommend this metal used in coastal areas. Again, it can be cleaned with Stainless Steel cleaning products or a solution of lemon juice and baking powder and wiped off with soapy water. In addition, we would suggest using an anti-corrosive spray such as ACF-50 which forms a clear film onto the surface of the fittings and adds protection to the surface for up to six months. We sell this on our website. /product/corrosion-block-anti-corrosion-formula-946ml-bottle-with-trigger-spray
201 STAINLESS STEEL
201 Stainless Steel is made up of Carbon, Manganese, Phosphorous, Sulphur, Silicon, Chromium, Nickel, Nitrogen, and Iron. It contains half the nickel and more manganese and nitrogen than the other popular steels. It is also the least expensive of the steel metals we sell. This mid-range product is prone to corrosion such as salt water and not suitable for coastal areas. Again, it can be cleaned with Stainless Steel cleaning products or a solution of lemon juice and baking powder. In addition, we would suggest using an anti-corrosive spray such as ACF-50 which forms a clear film onto the surface of the fittings and adds protection to the surface for up to six months. We sell this on our website. /product/corrosion-block-anti-corrosion-formula-946ml-bottle-with-trigger-spray
TEAK WOOD
Our Teak lighting use timber from a sustainable source, organically oiled during production to enhance and protect the grain. The teak bollards for example are made from a natural raw material which reacts to temperature changes and will naturally release sap or may sweat inside the protective packaging. So, please don’t be alarmed if you notice this when you unpack the bollards from their packaging. Once installed, they will weather naturally in the garden, although further oil, stain or varnish treatments are recommended periodically to preserve the beauty of these products. This should also help prevent the build-up of mildew and drying out from the sun. Teak Sealer and Teak oil can be purchased from many timber and DIY stores. They are suitable for all areas including coastal areas.
ALUMINIUM
Many of our products are made from aluminium which is formed of aluminium oxide in an ore called bauxite. Alumina and bauxite are the two main raw materials in the aluminium making process. Aluminium is obtained by the electrolysis of alumina which extracts pure aluminium metal from alumina. Aluminium will not rust however it does suffer from oxidation and is prone to corrosion. We would not recommend Aluminium products in coastal areas. To maintain the surface of the product you can clean with a solution of vinegar and water and rinse with soapy water. Again, our ACF-50 anti-corrosive spray will provide a clear protective coating to the surface of the fittings and can offer up to six months protection. /product/corrosion-block-anti-corrosion-formula-946ml-bottle-with-trigger-spray
POWDER COATED FINISHES
Many of our coloured finished products have been powder coated onto aluminium. This is a technique to apply decorative and protective finishes to aluminium through a process that electrostatically charges the powder consisting of a mixture of finely milled resin and pigment, spraying it on to the aluminium surface as a baking process. Although they look effective, please bear in mind that the powder is a paint and in coastal areas the paint can peel and expose the aluminium to corrosion. Therefore, we would not recommend powder coated aluminium fittings in coastal areas. To clean the surface simply use soapy water and a soft cloth and do not use anything abrasive as this will damage the finish. Again, our ACF-50 anti-corrosive spray will provide a clear protective coating to the surface of the fittings and can offer up to six months protection. /product/corrosion-block-anti-corrosion-formula-946ml-bottle-with-trigger-spray
ANODISED PAINT FINISH
Anodised coloured paint finishes give a lustre shiny finish to the surface of aluminium fittings and this is done by dipping the aluminium component into an acid electrolyte bath and applying an electric current to the liquid using a cathode. This causes oxygen ions within the aluminium to be released, which then combine with the aluminium atoms on the surface of the component to create the anodic oxide finish. This process gives the metal surface a porous structure, which can then be coloured with dyes and sealed afterwards. The advantage of the anodised finish is that it is not applied on the surface of the metal, instead, it is integrated with the aluminium substrate, which means it does not peel or chip like paint. The beauty of anodising is that it does not come off and it should protect the aluminium depending upon the thickness for at least 5 years and therefore reduce corrosion occurring. If used in coastal areas, we would recommend they are cleaned regularly with soapy water. Again, our ACF-50 anti-corrosive spray will provide a clear protective coating to the surface of the fittings and can offer up to six months protection. /product/corrosion-block-anti-corrosion-formula-946ml-bottle-with-trigger-spray
POLYCARBONATE (PC) –PLASTIC
Polycarbonate is a durable thermoplastic material with high impact resistance. It is quite light in weight and used primarily for Amenity style light fittings. It is fine for use in all areas including the coast. It should be cleaned periodically with warm soapy water to remove any deposits that have accumulated over time.
FeCSI-Steel
The element Iron (Fe) used in conjunction with steel alloys is put together to produce a product that eliminates the need for painting, and which forms a stable rust-like appearance after several years’ exposure to the weather. This product is used in some of our bollards under our ‘Rustic Bollard’ Category. They are very heavy and robust fittings. The surface oxidation of weathering steel takes approximately six months. When first purchased some residue rust colour from the manufactured product may be visible and will wash away with the elements of the weather. Over time they will naturally give a rust effect appearance and you will be able to touch them without any rust residue staining. An example of this is shown on our website for the ‘Rusty Slot’ fitting. They are ideal for all areas including the coast.
GRANITE
Granite is a coarse-grained igneous rock composed mostly of quartz, alkali feldspar and plagioclase. It is a hard semi-porous rock which is resistant to heat and cold. Ideal for any area, however salt deposits in coastal areas will accumulate onto the surface of the rock so it is advisable to clean the surface with warm soapy water periodically. Do not use anything abrasive.














































Delivery within 2 days